Question 1

How long will it take to receive my order?

Accepted Answer

Typically, it takes 3-5 business days to receive your order. We’re doing our best to deliver it promptly for you.

Question 2

Low wind speed/rainfall

Accepted Answer

To avoid affecting wind and rain measurements, as a rule of thumb, the sensor array should be mounted at least four times the height of the highest obstacle.

For example, if the building is 20 feet (6 meters) tall and the monitor pole is 6 feet (2 meters) tall, the mounting distance is 4 x (20 - 6)' = 56 feet (17 meters).

Common sense dictates that if the weather station is mounted next to a tall building, the wind and rain will not be accurate.

Question 3

Weather Station Installation Guide

Accepted Answer

Guidelines to installing your PWS

The location of your weather station is the most important part of installation. If your weather station is located under a tree or an overhang, the rainfall data measured by the station will not be correct. If you place your weather station in an alley, you could very well get a wind tunnel effect on the anemometer, resulting in erroneous wind data. Your weather station should have good "fetch", or distance from any other tall object.

Siting/ Installation Guide:
 
HTTP://www.wunderground.com/weatherstation/installationguide.asp

Question 4

I can't get the "S" to point south, what's the solution?

Accepted Answer

This picture will give you a reference. The mounting method is vertical. You can check it in the instruction manual 5.1.4.
figure 1

The cylinder needs to be embedded in the mounting base and mounting bracket back plate, held in place by screws.
figure 2
Thank you.

Question 5

What is the distance between the transmitter and the display?

Accepted Answer

We recommend placing the transmitter within 100 feet from the display in the event of interference from an obstruction. If in an open field, it may be placed within 300 feet.

Question 6

Can two "receivers" (displays) be connected to one transmitter?

Accepted Answer

Yes, but if the receiver (display) is too far away from the transmitter, it will not receive the signal. within 150 meters.

Question 7

Display brightness is too low

Accepted Answer

The display will remain on only when the power adapter is connected. The display backlight has 3 levels of brightness.

When the backlight is on, short press the SNOOZE button to switch between the 3 levels of backlight.

When the backlight is off, press and hold the SNOOZE button for 3 seconds and the backlight will turn on permanently. The BL ON icon will be displayed in the date area for 3 seconds.

To turn off the display backlight at any time, press and hold the SNOOZE button for two seconds. The BL OFF icon will appear in the date area for 3 seconds.

If the brightness cannot be adjusted, it means that the power adapter or the display interface has a poor contact problem.

Question 8

Optimal viewing angle for the display

Accepted Answer

The folding tabletop stand on the back of the display console is at roughly 45 degrees to the display . We recommend viewing the console from a 20 degree to 30 degree angle from above for the best display of the screen.

Question 9

How to troubleshoot if the SA9 weather station is showing 0 barometric pressure.

Accepted Answer

You can reset the display console to factory defaults by pressing and holding the MAX/MIN/- key for at least three seconds while plugging in the power supply. Then unplug the display and plug it back in. (Remove the batteries before doing this).

If any data is not displayed, press and hold the CHANNEL/+ key for three seconds until a click is heard and all data is displayed as dashed lines.
The display will reacquire the signal from the transmitter. Once the signal is reacquired, all data will be displayed.

Question 10

Definition of rainfall day and rainfall event in the app

Accepted Answer

The logic of our event is based on this. We take 24 hours of data. If the accumulated rainfall in 24 hours is less than 10 mm (0.039 inches), it will be reset to zero. If it is greater, it will display the rainfall in 24 hours.

Day is the rainfall in 24 hours.

Question 11

After updating the firmware, outdoor data is not displayed

Accepted Answer

The device will automatically search for the outdoor unit signal. If it fails, you need to press the outdoor unit reset button. You will also need to reconnect the outdoor and indoor units if you lose signal.If any sensor communication is lost, dashes (--.-) will appear on the screen. To reacquire the signal, press and hold the CHANNEL/+ button for 3 seconds, select the lost sensor, and the remote search icon will display continuously.It is also necessary to press the reset button on the outdoor unit. When the signal is reacquired, the remote search icon will turn off and the current value will be displayed. Also need to change the outdoor unit batteries.

Question 12

Steps to connect to wifi (Bluetooth mode is recommended)

Accepted Answer

1.Please turn on Bluetooth mode in your phone first. 2.Press and hold the MAX/MIN/- key to enter the distribution network mode, the WiFi icon will flash and the BI icon will be shown in the date area. After the display enters the " Bluetooth distribution network " mode, please open the APP to start networking 3.Please follow the steps in the app to connect to the network. Select the product model, name the device, and locate the address. 4.Quickly review the three steps to connect to WiFi. 5.Scan the QR code on the back of the display and select the Bluetooth network mode. The device will automatically search. After the connection is successful, please select a 2.4ghz router and enter the password. After successfully connecting to WiFi, the current device will be displayed in the app.

Question 13

How to Download Forms

Accepted Answer

You can download data in the profile section of the app.
Select the start and end time you want to download the data. The document will be saved in your files.

Question 14

The app only records data points once per hour. How can I increase the frequency of recording to accurately reflect wind gusts?

Accepted Answer

The table records data every 5 minutes.
The line chart records data every 1 hour. Select the time you want to view the data. The larger the time span, the more you slide your finger a little bit, and the time displayed may be an hour.

Question 15

My display shows the wrong wind direction

Accepted Answer

Please remove the battery and then reinstall it. With the entire sensor in the inverted position (rain gauge facing downward, the sensor head oriented N/S or S/N - depending on hemisphere, and the weather vane pointed North.Figure 1 shows the rain gauge barrel. The number 2 in Figure 2 is the head of wind vane.Figure 1Figure 2

Question 16

Where can I find a video on how to connect to WiFi?

Accepted Answer

You can check out the video on the SA9 Bluetooth connection in the help section of the app profile. It might help you

Question 17

The device name in the app cannot exceed 20 characters.

Accepted Answer

Device name, location naming requirements: only numbers, upper and lower case letters, maximum 20 characters, spaces allowed, symbols prohibited.

Spaces are also included in the 20 characters.

Question 18

The WU interface of the app does not display pressure

Accepted Answer

The wu interface in the app can only receive information from the outdoor unit, and the indoor device cannot transmit.
You checked the pressure on the weather underground website.

Question 19

The device shows as offline.

Accepted Answer

If the device is frequently offline, it must be reset. The router should always
be on, it will show offline after no WiFi.

Question 20

Where can I find the API key?

Accepted Answer

Please see sample pic below for your reference where to find the API keys. When you hit on the API keys tab under Member Settings, here's what will show up.

Question 21

Battery Issues

Accepted Answer

Reason for continuous alarms after power outage:Our device consumes a lot of power, and the battery life is very short. A brand new battery only lasts about 1-2 hours. A low battery will cause the device to constantly power on and off, making a beeping sound. So you need to replace the battery or use an adapter; otherwise, the beeping sound will continue.The function of the battery on the display:Since our devices lack data storage capabilities, the app cannot retrieve data generated during power outages. The battery's function is to ensure the device operates normally during power failures.

Question 22

Definition of wind speed

Accepted Answer

The wind speed displayed is the average wind speed over a 15-minute period. If there's no wind, GUST should display 0. If there's wind, GUST will immediately display it.

Question 23

How to connect the outdoor unit and indoor unit?

Accepted Answer

You can follow the steps below to connect the outdoor unit and display screen. 1. First, press the CHANNEL+ button for 3 seconds. Other icons on the screen will go out and the search icon will start to flash.2. Next you need to press the outdoor transmitter Reset key once, and the LED light will blink. Outdoor Transmitter and console will start pairing.3. Finally, screen search icon does not flash, complete pairingFor small sensor paring:Press and hold the ALARM button on the right side of the display to enter sensor pairing mode. And then press the small sensor' button.

Question 24

How to connect the outdoor unit and indoor unit?

Accepted Answer

Pairing the indoor and outdoor units:Press and hold the TEMP button for at least 3 seconds, then press the Reset button on the outdoor unit once.

Question 25

Steps to connect to wifi (Bluetooth mode is recommended)

Accepted Answer

1.Please turn on Bluetooth mode in your phone first.2. Press and hold the WIND + key to enter the distribution network mode, the WiFi icon will flash and the BI icon will be shown in the date area.After the display enters the " Bluetooth distribution network " mode, please open the APP to start networking3.Please follow the steps in the app to connect to the network.Select the product model, name the device, and locate the address.4.Quickly review the three steps to connect to WiFi.5.Scan the QR code on the back of the display and select the  " Bluetooth distribution network " mode.The device will automatically search. After the connection is successful, please select a 2.4Ghz router and enter the password.After successfully connecting to WiFi, the current device will be displayed in the app.

Question 26

Batteries should only be used in emergencies

Accepted Answer

Please use the adapter to power the device! The battery is for  emergency use only!The battery only lasts for a maximum of two hours!

Question 27

Calibration steps

Accepted Answer

1.Press and hold the TEMP and MAX/MIN buttons at the same time for 3 seconds to enter calibration mode. The CAL icon will be displayed.2.Press the SET key to switch.3.Press the WIND+ key or PRESSURE- key to increase or decrease the temperature reading Press and hold the WIND+ key or PRESSURE- key for three seconds to quickly increase or decrease the temperature reading.4.Press the ALARM key to reset the current value.  5.Press the LIGHT SNOOZE to exit the mode.

Question 28

Set Time and Date

Accepted Answer

You can follow the steps below to set the date and time.1. While in Normal Mode, press and hold the SET key for at least three seconds to enter the Set Mode.2. When the 12/24 hour format will flash, press the SET key again to set the hour. Press the WIND + or PRESSURE- key to adjust the hour up or down.3. Press the SET key again to set the minute. Press the WIND + or PRESSURE-  key to adjust the minute up or down.4. Please press the SET key twice until the month flashes. Press the WIND + or PRESSURE- key to adjust the calendar month.5. Press the SET key again to set the calendar day. Press the WIND + or PRESSURE-  key to adjust the calendar day.6. Please press the LIGHT SNOOZE key to exit the setting mode.

Question 29

Outdoor temperature inaccurate

Accepted Answer

Please check if the outdoor temperature display shows Dew Point data. If it does, please press the TEMP button to switch data.

Question 30

How to connect the outdoor unit and indoor unit?

Accepted Answer

Pairing the indoor and outdoor units:Press and hold the TEMP button for at least 3 seconds, then press the Reset button on the outdoor unit once.

Question 31

Set Time and Date

Accepted Answer

You can follow the steps below to set the date and time.1. While in Normal Mode, press and hold the SET key for at least three seconds to enter the Set Mode.2. When the 12/24 hour format will flash, press the SET key again to set the hour. Press the WIND + or PRESSURE- key to adjust the hour up or down.3. Press the SET key again to set the minute. Press the WIND + or PRESSURE-  key to adjust the minute up or down.4. Please press the SET key twice until the month flashes. Press the WIND + or PRESSURE- key to adjust the calendar month.5. Press the SET key again to set the calendar day. Press the WIND + or PRESSURE-  key to adjust the calendar day.6. Please press the LIGHT SNOOZE key to exit the setting mode.

Question 32

Calibration steps

Accepted Answer

1.Press and hold the MAX/MIN buttons at the same time for 3 seconds to enter calibration mode. The CAL icon will be displayed.2.Press the SET key to switch.3.Press the WIND+ key or PRESSURE- key to increase or decrease the temperature reading Press and hold the WIND+ key or PRESSURE- key for three seconds to quickly increase or decrease the temperature reading.4.Press the ALARM key to reset the current value.  5.Press the LIGHT SNOOZE to exit the mode.

Question 33

Outdoor temperature inaccurate

Accepted Answer

Please check if the outdoor temperature display shows Dew Point data. If it does, please press the TEMP button to switch data.

Question 34

How to set the date and time

Accepted Answer

You can follow the steps below to set the date and time. 1. While in Normal Mode, press and hold the SET key for at least three seconds to enter the Set Mode. 2. When the SYNC will flash, press the SET key again to set the hour. Press the MIN/MAX/- key to adjust the hour up or down. 3. Press the SET key again to set the minute. Press the CHANNEL/+ key or MIN/MAX/- key to adjust the minute up or down. 4. Please press the SET key twice until the month flashes. Press the CHANNEL/+ key or MIN/MAX/- key to adjust the calendar month. 5. Press the SET key again to set the calendar day. Press the CHANNEL/+ key or MIN/MAX/- key to adjust the calendar day. 6. Please press the SNOOZE key to exit the setting mode.

Question 35

Why is the time on the display incorrect?

Accepted Answer

Yes, the date and time can be set even without connecting to WiFi.

Please pay attention to whether the device has the automatic sync setting (SYNC) turned on.
If connected to WiFi, the device will automatically sync to the Internet time.

Question 36

Why does the display keep beeping?

Accepted Answer

Please update your device to the latest firmware
The beeping sound is because the battery is low and the unit is trying to power on but can't.
The display will only work for a maximum of 2 hours on battery power alone because uploading data consumes battery power.
We recommend that the display be plugged in to the power adapter at all times.
We apologize for the inconvenience.

Question 37

Why does the outdoor humidity on the display say 0%?

Accepted Answer

The outdoor sensor is not waterproof, please make sure it is in a dry and cool place.

Question 38

If the router is disconnected, can the device automatically connect and show online?

Accepted Answer

Make sure the display is SYNC-enabled. If enabled, it will automatically synchronize with the Internet time.

Question 39

Outdoor sensors are not waterproof

Accepted Answer

Make sure to place the outdoor sensor in a dry and cool place.

Question 40

How to turn off the alarm

Accepted Answer

Press and hold the ALARM key once to enter the alarm mode.Press and hold the SET key for three seconds. The first alarm parameter will begin flashing. To save the alarm setting and proceed to the next alarm parameter, Press (do not hold) the SET key. To adjust the alarm parameter, press the [+] or [-] key to increase or decrease the alarm setting slowly, or press and hold the [+] or [-] key for three seconds to increase or decrease the alarm setting rapidly. Press the ALARM key to turn on (the alarm icon will appear ) and off the alarm.Press the SNOOZE key twice at any time to return to the normal mode.

Question 41

How to pair the outdoor unit and indoor unit (first time)

Accepted Answer

1.Plug in the device with the power adapter.2.Please press and hold the "Pair" button for 3 seconds to enter the Pairing mode, the indicator light (red) flashes fast, the indicator light (red, green) will flash alternately after successful pairing. 3.You also need to press the reset button on the outdoor unit, and the device will automatically search for signals for pairing. To confirm whether the pairing is successful, check whether there is data in the app. Note: Please connect the wifi first. If you subsequently lose connection, press and hold the pairing button again. It will automatically search for a signal.

Question 42

Steps to connect to wifi (Bluetooth mode is recommended)

Accepted Answer

1.Please turn on Bluetooth mode in your phone first. 2. Please press and hold the "Internet" button for 3 seconds, the device will enter the network mode. By default, the first network mode is "Bluetooth distribution network" mode, the indicator light (green) blinks about 0.5s kind of blinking once. 3.Please follow the steps in the app to connect to the network. Select the product model, name the device, and locate the address. 4.Quickly review the three steps to connect to WiFi. 5.Scan the QR code on the top of the gateway and select the Bluetooth network mode. The device will automatically search. After the connection is successful, please select a 2.4ghz router and enter the password.

Question 43

I can no longer see outdoor data on the app, what should I do?

Accepted Answer

1.Please press and hold the "Reset" button for 3 seconds, the gateway will disconnect the pairing with the transmitter.2.Then please reset the transmitter.After the transmitter is powered on and working properly, the display has to be re-plugged in to re-receive the transmitter signal. It usually takes 1-3 minutes to receive the data, do not operate the keys or power off until the transmitter data is received.Install a new set of batteries for the remote sensor. In cold weather environments, install lithium batteries.3.Plug in the device with the power adapter.Please press and hold the fourth button for 3 seconds to enter the pairing mode, the indicator light (red) flashes fast, the indicator light (red, green) will flash alternately after successful pairing.4.If the device shows offline on the app, you need to reconnect to WiFi.

Question 44

Button Definition

Accepted Answer

Reset: Please press and hold the "Reset" button for 3 seconds, the gateway will disconnect the pairing with the transmitter. Rain Reset: Please press and hold the "Rain Reset" button for 3 seconds, all rain values will be cleared to zero (current hour, 24 hours, week, month). Internet:  WiFi connection(3 modes)  "Bluetooth Distribution Network Mode, WiFi Distribution Network Mode, Web page distribution Network Mode.Paring: Please press and hold the "Paring" button for 3 seconds to enter the pairing mode, the indicator light (red) flashes fast, the indicator light (red, green) will flash alternately after successful pairing. One click to exit pairing mode.

Question 45

Humidity is not accurate

Accepted Answer

Our device is not waterproof

Where did you place the device?

If water gets in, the humidity will be inaccurate.

Question 46

How to connect the wifi (only one method:bluetooth distribution method)

Accepted Answer

1.Please turn on the Bluetooth mode of your phone first Open the "Weatherseed" App, and select "Add Device" and choose the product category (Portable Weather Station) and model (SA3). 2.Manually enter the device name and address and click "Next". 3.Please press and hold the "paring" button on the right of the device to enter the "Bluetooth distribution network" mode, the indicator will flash blue once . 4. Clicks the "Weatherseed-xxxx". Then the app automatically pairs with the device via Bluetooth. Upon successful pairing, it will automatically proceed to the next interface. 5.Enter the WiFi(2.4Ghz) password and click "Start binding" to configure the network . 6.Enter the device group name and click "Save" to save the settings . 7.Once saved successfully, the device information will be displayed .

Question 47

cannot connect WiFi

Accepted Answer

Sorry for the inconvenience.

Please turn to use WSView Plus app, if you are using WS View app. Then please click the "+" icon to add a new device and follow the steps prompted in the app to connect the weather station to WiFi.

You can follow the user manuals 8.1 and 8.2 for wifi connection. Meanwhile, please follow the user manual 11. Troubleshooting Guide for no wifi connection troubleshooting.

Question 48

WiFi is disconnected suddenly

Accepted Answer

1.Please confirm whether your network is normal and whether your router account number and password are correct (especially pay attention to uppercase and lowercase letters).2.When pressing WIND+PRESSURE (about 5 seconds later), please check whether there is a blue light flashing on the back of the display.3.Please use WSView Plus, if you are using WS View.

Question 49

3500 time set/sync

Accepted Answer

While base station connected with the internet, the time will be updated to internet time automatically. Time zone and DST will be automatically synchronized from internet.

So you need to set the correct address and time zone in the device properties on ecowitt. You can check the pic below.

Question 50

DST

Accepted Answer

If customer didn't upload data to ecowitt.net, the time zone is defined based on the customer's IP address.DST is subject to time zone.If you set uploaded data to ecowitt.net, please set the correct time zone on the website and make sure the "Automatically adjust clock for daylight saving changes is active.The time and DST will be lautomatically synchronized from ecowitt server.

Question 51

3500 Firmware Update

Accepted Answer

The latest is WiFi firmware is V5.1.5. 
You can usually see the version of the device directly on the app or on the server.
If it is not the latest. There will be a message popping up when you click on the device.

Question 52

3500 display screen size

Accepted Answer

The screen size of 3500 is as follows:Frame Dimensions : 7.36x4.60x0.79inch (187x117x20mm) LCD Dimensions: 6.18x2.95inch (157x75 mm)

Question 53

outdoor data issues

Accepted Answer

Please troubleshoot according to the following methods. The first method. 1. With an open-ended paperclip, press the reset button for 3 seconds to completely discharge the voltage. 2. Take out the batteries and wait one minute, while covering the solar panel to drain the voltage. 3. Put batteries back in and resync the console with the sensor. The second method. 1. Please replace the batteries in the outside sensor. 2. If the batteries were recently replaced, please check whether the batteries are inserted backwards. The third method. 1. If the LED next to the battery compartment is flashing every 16 seconds, there may be a temporary loss of communication due to reception loss related to interference or other location factors. 2. Or you can power down and up the console. Just remove AC power and batteries, wait 10 seconds, and reinsert AC power and batteries. The fourth method. You can press WIND/+ and PRESSURE /- key to reset the weather station and clear all user settings to default.

Question 54

indoor data issues

Accepted Answer

Please restore the console to its factory default settings, please follow these steps strictly:1. Remove the power from the console by removing the batteries and disconnecting the AC adapter. 2. Apply power by connecting the AC adapter. 3. Wait for all of the segments to appear on the screen. 4. Press and hold the WIND/+ and PRESSURE/- keys at the same time until the console power up sequence is complete (about 5 seconds). When pressing WIND+PRESSURE (about 5 seconds later), please check whether there is a blue light flashing on the back of the display. 5. Replace the batteries. Even though the display has been reset, there will still be data displayed on it because the display is still receiving signals from the transmitter in real time. If you want to reset the Weather Underground and Ecowitt website data, you can contact the website customer service. We apologize that the WSview plus app cannot reset the data.

Question 55

data is inaccurate

Accepted Answer

You can calibrate the outdoor temperature by following the steps below. 1. Hold the TEMP. and MAX/MIN key together for 5 seconds to enter calibration mode. 2. Press the SET key repeatedly until the outdoor temperature is displayed. 3. Press the WIND/+and PRESSURE/- key to adjust values.Press the ALARM key to reset any adjusted value.4. Press the LIGHT /SNOOZE key at any time to exit. 1) Indoor temperature offset calibrated (range +/-5˚C, default: 0 degrees) 2) Indoor humidity offset calibrated (range +/-10%) 3) Outdoor temperature offset calibrated (range +/-5˚C, default: 0 degrees) 4) Outdoor humidity offset calibrated (range +/-10%) 5) Absolute pressure offset calibrated (range +/-50hpa) 6) Wind direction offset calibrated (adjust by degree) 7) Wind speed factor adjust, default 100% (range 50% to 150%) 8) Rain factor adjust, default 100% (range 50% to 150%)

Question 56

rain gauge problems

Accepted Answer

Please gently pour water down inside the rain collector and check if the display rain data changes. If the rain data changes, the rain gauge is fine and you need to calibrate the rain data. You can calibrate the item by following the steps below. 1. Hold the TEMP. and MAX/MIN key together for 5 seconds to enter calibration mode. 2. Press the SET key repeatedly until the corresponding item which you want to calibrate is displayed. 3. Press the WIND/+and PRESSURE/- key to adjust values. Press the ALARM key to reset any adjusted value. 4. Press the LIGHT /SNOOZE key at any time to exit.

Question 57

How to switch to view rainfall range

Accepted Answer

Press  Rain key to view Rain Rate, event, Rain Day, 
Rain Week, Rain Month, and Rain total
Press the RAIN key 2s to reset current display rain

Question 58

Want to view historical data online

Accepted Answer

You can customize the time to view historical data on the Ecowitt website.

Day, 24 hours, meteorological day, week, month, year, 7 days, 30 days, customized.

Question 59

Upload data time

Accepted Answer

The 3500 uploads to WU every 40 seconds, and to Ecowitt every 1 minute.
The upload time of Ecowitt can be set in the Ecowitt app or on WS view plus.

Question 60

If I have a Sainlogic 3500 weather station and I have connected it to Ecowitt, can I receive messages/text messages? For example, how can I receive messages when the wind speed exceeds a certain value?

Accepted Answer

You can receive notifications via the email address you registered with ecowitt.
You can customize your preferences and notification frequency.

Question 61

Is it possible to upload to a custom website.

Accepted Answer

This model 3500 can be uploaded to a custom site.

Please download ws view plus and check Wunderground or EcoWitt to find out what protocols they use, then select the same protocol in your customized site to upload the data.

Check if your local server is using the same protocol as Wunderground or EcoWitt.
If the protocols are not the same, you cannot upload data.

Question 62

3500WiFi is disconnected suddenly

Accepted Answer

1.Please confirm whether your network is normal and whether your router account number and password are correct (especially pay attention to uppercase and lowercase letters).
2.When pressing WIND+PRESSURE (about 5 seconds later), please check whether there is a blue light flashing on the back of the display.
3.Please use WSView Plus, if you are using WS View.

Question 63

Temperature is inaccurate

Accepted Answer

You can first calibrate the temperature. In normal mode, press and hold the SET and CHANNEL/+ keys at the same time for five seconds to enter the temperature calibration mode. The indoor temperature will begin flashing.Press the [+] or [-] key to increase or decrease the temperature reading (in increments of 0.1). Press and hold the [+] or [-] key for three seconds to increase or decrease rapidly. Press the ALARM key and reset to current value. Press the SET key switch to sensor temp calibration mode. Press the SET key to exit calibrated mode, or press the SNOOZE button at any time. Light source can also cause inaccurate temperatures. You can also stand the sensor up for better ventilation. We recommend that you put the sensor and the display together and it will take about 3-5h of standing time for them to stabilize. If the temperatures are still very different, please contact us by email. Also please provide us with a screenshot of your order with the purchase order number.

Question 64

Switching Temperature and Dew Point

Accepted Answer

While in Normal Mode, press (do not hold) the SET key repeatedly to enter into Temperature and Dew Point. Press the [+] or [-] key to toggle between temperature and dew point. To exit the Quick SET Mode at any time, press the SNOOZE button of the display console.

Sainlogic

Your cart is empty

Cart • 0 items

Frequently Asked Questions

Country/region

Language